Open Access
Issue |
EPJ Web Conf.
Volume 183, 2018
DYMAT 2018 - 12th International Conference on the Mechanical and Physical Behaviour of Materials under Dynamic Loading
|
|
---|---|---|
Article Number | 02056 | |
Number of page(s) | 6 | |
Section | Experimental Techniques | |
DOI | https://doi.org/10.1051/epjconf/201818302056 | |
Published online | 07 September 2018 |
- Anonymous "Automotive Steel Definitions," Available: http://www.worldautosteel.org/steelbasics/automotive-steel-definitions/. [Google Scholar]
- Anonymous "Weight reduction and fuel economy" available :http://www.worldautosteel.org/steelyourworld/mass-reduction/ [Google Scholar]
- Anonymous "Mass Reduction: a Report by FKA" availbele :http://www.worldautosteel.org/projects/mass-reduction/mass-reduction-a-report-by-fka/ [Google Scholar]
- Anonymous "Stainless Steel New Applications in Automotive Applications" http://www.worldstainless.org/transport_applications/automotive_applications- [Google Scholar]
- Mohr, D., Marcadet, S.J., Micromechanicallymotivated phenomenological Hosford.Coulomb model for predicting ductile fracture initiation at low stress triaxialites. Int. J. Solids Struct. 67-68, 40-55 (2015) [Google Scholar]
- Eller, T., Greve, L., Andres, M., Medricky, M., Hatscher, A., Meinders, V., Van den Boogaard, A., Plasticity and fracture modeling of quenchhardenable boron steel with tailored properties. J. Mater. Process. Technol. 214, 1211-1227 (2014) [Google Scholar]
- Bardelcik, A., Worswick, M., Winkler, S., Wells, M., A strain rate sensitive con-stitutive model for quenched boron steel with tailored properties. Int. J. Impact Eng. 50, 49-62 (2012) [CrossRef] [Google Scholar]
- Dzugan, J., et al., Identification of ductile damage parameters for pressure vessel steel. Nucl. Eng. Des. (2015), http://dx.doi.org/10.1016/j.nucengdes.2015.12.014 [Google Scholar]
- Petr Kubík, P., Šebek, F., Petruška, J., Hůlka, J., Růžička, J., Španiel, M., Džugan, J., Prantl, A.: Calibration of Selected Ductile Fracture Criteria Using Two Types of Specimens, Key Engineering Materials, ISSN: 1662-9795, 592-593, pp.258-261 (2013) [CrossRef] [Google Scholar]
- Lee, Y.W., Wierzbicki, T.,"Quick Fracture Calibration for Industrial Use," Massachusetts Institute of Technology, Impact & Crashworthiness Laboratory Report No. 115, Numerical failure analysis of three-point bending on martensitic hat assembly using advanced plasticity and fracture models for complex loading (2004) [Google Scholar]
- Abaqus FEA. SIMULIA web site. Dassault Systemes [Google Scholar]
- Ehlers S. Strain and stress relation until fracture for finite element simulations of thincircular plate. Thin-Walled Structures, 48 (1): 1-8 (2010) [CrossRef] [Google Scholar]
- Bao Y, Wierzbicki T., Evaluation and calibation of seven fracture models. J Mech Phys Solids, submitted for publication (2004) [Google Scholar]
- Stephane J Marcadet, Christian C Roth, Borja Erice and Dirk Mohr, "A rate-dependent hosford-coulomb model for predicting ductile fracture at high strain rates," in Jan 1, pp. 1080 (2015) [Google Scholar]